 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Order this document by MC44145/D MC44145 Pixel Clock Generator/ Sync Separator The MC44145, Pixel Clock Generator, is a component of the MC44000 family. The MC44145 contains a sync separator with composite sync and vertical outputs, and clock generation circuitry for the digitization of any video signal along with the necessary circuitry for clock generation, such as a phase comparator and a divide-by-2 to provide a 50% duty cycle. The MC44145 is available in a SO-14 package and is fabricated in the Motorola high density, high speed, low voltage, process called MOSAIC 1.5(R). PIXEL CLOCK GENERATOR/ SYNC SEPARATOR SEMICONDUCTOR TECHNICAL DATA MOSAIC is a trademark of Motorola, Inc. 14 1 Representative Block Diagram Sync Out Fref Video In 9 12 VCC Sync Sep 11 A Sync Separator B 3 5 C 4 A In Sync Amp Out 10 Div 2 EN 8 D SUFFIX PLASTIC PACKAGE CASE 751A (SO-14) PIN CONNECTIONS NPD Gain 1 Gnd 2 14 PLL Loop Filter 13 NBACK 12 Video In 11 VCC2 10 Sync Amp Out 9 8 (Top View) Fref Div 2 EN Phase and Frequency Comparator Up Charge Pump Dn Sync B 3 VC VCO B2 Sync Amp In 4 FO 2FO Sync C 5 VCC 6 Clock Out 7 MC44145 6 VCC 13 NBACK 1 NPD Gain 14 R C2 C External Divider Device This device contains 214 active transistors. MC44145D PLL Loop Filter 7 Clock Out 2 Gnd ORDERING INFORMATION Operating Temperature Range TA = 0 to +70C Package SO-14 (c) Motorola, Inc. 1996 Rev 0 MOTOROLA ANALOG IC DEVICE DATA 1 MC44145 MAXIMUM RATINGS Rating Supply Voltage Storage Temperature Range Operating Junction Temperature NOTE: ESD data available upon request. Symbol VCC VCC2 Tstg TJ Value 6.0 6.0 -65 to +150 +150 Unit V C C RECOMMENDED OPERATING CONDITIONS Characteristic Supply Voltage Video Input Amplitude (Note 2) NBACK Pulse Width Fref Pulse Width Operating Ambient Temperature Symbol VCC VCC2 Vin NBACK Fref TA Pin 6 11 12 13 9 - Min 4.75 4.75 0.4 100 100 0 Typ 5.0 5.0 1.0 500 500 - Max 5.5 5.5 2.5 - - +70 Unit Vdc Vpp ns ns C ELECTRICAL CHARACTERISTICS Characteristic POWER SUPPLY Supply Current (Note 1) Supply Current ICC ICC2 - - 6 11 - - 15.5 300 - - mA A Symbol Note Pin Min Typ Max Unit SYNC SEPARATOR (VCC = 5.0 V; TA = 25C, unless otherwise specified.) Sync B Output Sync C Output (1.0 mA Source) Slicing Level (SL) Video Input Sink Current Video Input Source Current 2. Positive Video. 3. High impedance output. 4. Low impedance output. - - - - - 3 4 - VPin 12 < SL VPin 12 > SL 3 5 12 12 12 - - - - - 5.0 to 0 0 to 3.3 VCC/2 18 1.2 - - - - - V V V A A NOTES: 1. Operating current for Pin 6 is dependent on the clock frequency (Pin 7). Values given are specified for Pin 14 = 4.0 V. 2 MOTOROLA ANALOG IC DEVICE DATA MC44145 ELECTRICAL CHARACTERISTICS (continued) Characteristic Note Pin Min Typ Max Unit SYNC SEPARATOR (VCC = 5.0 V; TA = 25C, unless otherwise specified.) VCO (VCC = 5.0 V; TA = 25C, unless otherwise specified, divider disabled.) Fmin Fmax Control Range Transfer Function Input Resistance Charge Pump Phase Jitter 1, 5 1, 4 2 1 9 6 7 8 7, 8, 14 7, 8, 14 14 7, 8, 14 14 1, 14 7, 9 - 39 1.0 - 0.5 - - - - 42 - 14 - 40 80 - 10 - 4.0 - - - - 3.0 MHz MHz V MHz/V M A ns INPUT BUFFERS (Fref AND NBACK) (TA = 25C, unless otherwise specified.) Threshold (TTL Compatible) Input Current OUTPUT BUFFER CLOCK (TA = 25C, unless otherwise specified.) Sync Amplifier Output High Level Sync Amplifier Output Low Level Rise Time Fall Time Load Capacitance NOTES: 1. Internal divider disabled. 2. 0 V stops the oscillator. 3. Divider /2 active. 4. VC = 4.0 V. 5. VC = 1.0 V. 6. PFD gain low. 7. PFD gain high. 8. VCO alone. 9. VC = 4.0 V, charge pumps off. 10. 2 LSTTL loads. 11. With cap load 15 pF and between 10 and 90% of 0.4 and 2.4 V. - - 9, 13 9, 13 - - 2.5 - - 1.0 V A 1.0 mA Source 1.0 mA Sink 11 11 10 10 10 10 10 10 2.4 - - - - 3.0 0.2 - - 15 - 0.4 6.0 6.0 - V V ns ns pF MOTOROLA ANALOG IC DEVICE DATA 3 MC44145 CIRCUIT DESCRIPTION Composite Sync Separator The composite sync separation section is comprised of two blocks, a sync slicer and a sync amplifier, which can be used to extract the vertical sync and composite sync information from a video signal. The sync separator is an adaptive slicer in which the video signal is slightly integrated and then sliced at a ratio of 4.7 to 64 which corresponds to the sync to horizontal ratio. Two outputs are given, one of high impedance and the other low impedance. A slicing sync inverting amplifier is also on-chip, allowing one output to be used for composite sync and the other output to be integrated and then sliced using the slicing amplifier to extract the vertical sync information. Clock Generation The clock generation is made up of a wide ranging emitter-coupled VCO followed by a switchable /2 to provide a 50% duty cycle wherever required, or twice the set frequency if an external divider is used. The clock generator is a PLL subsection; its function is the generation of a high frequency, line locked clock that is used for video sampling and digitizing. The clock output is a LSTTL-like buffer which has a limited drive capability of two LSTTL loads. The VCO is driven from a charge pump with selectable current. The charge pump is driven by the phase comparator. The phase comparator is a type IV "phase and frequency comparator" sequential circuit. The clock generator, the heart of a PLL, is to be closed by means of an external divider, thus setting the synthesized frequency. This divider could be implemented in discrete logic or be a part of an ASIC subsystem. Phase and Frequency Comparator The phase comparator is fed from two input buffers, Fref which expects a reference frequency at line rate and that is rising edge sensitive, and NBACK which comes from the external divider and is falling edge sensitive. Charge pump current and output divider action are controlled by applying suitable voltage on the appropriate pins (respectively, NPD Gain and Div 2 EN). PIN FUNCTION DESCRIPTION Pin 1 2 3 4 5 6 7 8 9 Function NPD Gain Ground Sync B Sync Amp In Sync C VCC Clock Out Div 2 EN Fref Description This pin sets the gain of the phase frequency detector by changing the current of the charge pump output (40 A or 80 A). Low current with this pin > 2.0 V, high current for < 0.5 V. Ground connection common to the PLL and sync separator sections. High impedance sync output. Sync amplifier input. Low impedance sync output. Power connection to the PLL section. VCO clock output. Capable of limited LSTTL drive. It should not be used to drive high capacitive loads, such as long PCB traces or coaxial lines. The divider is switched in with this pin > 2.0 V; switched out for < 0.5 V. Reference frequency input to the phase and frequency comparator. Typically this will be a 15625 (15750) Hz signal. It is rising edge sensitive. Due to the nature of the phase and frequency comparator, no missing pulses are tolerable on this input. In a typical setup, this signal can be provided by the MC44011. Sync amplifier output. Power connection to the sync separator and amplifier. Video signal input to the sync separator. Fed by the external clock divider. Sets the multiplication ratio of the loop in multiples of the Fref frequency. Negative edge sensitive. See loop filter calculations at the end of this document. 10 11 12 13 14 NOTE: Sync Amp Out VCC2 Video In NBACK PLL Loop Filter The two VCC pins are not independent, as they are internally connected by means of the input protection diodes; they must always be both connected to a suitable VCC line. 4 MOTOROLA ANALOG IC DEVICE DATA MC44145 CIRCUIT OPERATION Composite Sync Separator The sync separator is an adaptive slicer. It will output "raw" sync data. Two outputs are given, thus allowing one output to be used for composite sync and the other output to be integrated and then sliced using the inverting slicing amplifier provided. As the input of the slicing amplifier is external, the amplifier may be driven from either sync output, although normally the high impedance output (Sync B) would be recommended. The positive video input signal required is nominally 1.0 V sync-to-white, but the circuit supports signals above and below this level and also is resistant to a degree of reflections on the signal. Coupling to the sync separator may be achieved by a simple capacitor of 100 nF, but better results may be obtained with a higher value in series with a resistance of 1.0 k. Clock Generator The system is best put to use in a dual loop configuration; a first loop locks to line frequency by means of a type I phase detector (multiplier type) which is insensitive to missing pulses. This PLL is then followed by a second loop using the MC44145, performing frequency multiplication. The phase comparator of the MC44145 is frequency and phase sensitive. It is a type IV (sequential type) phase detector, which does not tolerate missing pulses. The dual loop structure makes up a noise insensitive frequency (and phase) locked loop. The phase and frequency comparator provides two logical outputs, mutually exclusive - up or down - that are used to source or sink current to and from the loop filter. This current can be user-selected to be 40 A or 80 A (typical), thus providing some degree of loop gain control. The VCO is an emitter-coupled multivibrator type, with an on-chip timing capacitor, and has been designed for low phase noise. The divide-by-2 is included at the output of the VCO, thus allowing for a precise 50% duty cycle, hence the VCO is operating at twice the required frequency. The divider can be bypassed, bringing the VCO output directly to the output buffer. The external divider must provide a feedback pulse to close the loop; the falling edge of this pulse will be aligned (when the loop is in lock) with the rising edge of the pulse applied to the Fref input. Operation of the phase comparator is insensitive to the duty cycle of both its inputs. The feedback pulse should have a minimum width of 500 ns. This can be guaranteed if it has a length of at least 16 output clock cycles (highest output frequency with the divider disabled). APPLICATION INFORMATION Analog video signals out of the MC44011 are sampled and converted to 8-bits digital in the A/D converter (MC44250 series) by means of the clock provided by the MC44145, pixel clock generator (see Figure 1). The frame store contains the memory, the necessary logic for the memory addressing, as well as the counter to set the frequency multiplication ratio of the line locked clock generator (H. Count). Figure 1. Application Block Diagram R (Y) Video Digital Multistandard Decoder MC44011 G (U) B (V) MC44250 A/D Converter Frame Store R (Y) G (U) B (V) Pixel Clock Pixel Clock Generator MC44145 H. Count Vertical Sync MOTOROLA ANALOG IC DEVICE DATA 5 MC44145 Figure 2. 1.0 F Video In 1.0 k Sync C Sync Separator Sync B Amp C R V Sync Out C = 180 pF, R = 120 k H Sync Out Figure 3. Typical VCO Transfer Characteristics 60 FREQUENCY AT PIN 7 (MHz) 50 40 30 20 10 0 1.0 Pin 8 = Low 2.0 3.0 4.0 PIN 14 VOLTAGE (V) Figure 4. Sync Separator Timing Video Input (Pin 12) 0.2 s Sync C Out (Pin 5) 3.4 V 0V 1.0 s 5.0 s Composite Sync Input (Pin 12) D1 = 9.5 s Vertical Sync Out (Pin 10) D2 = 9.5 s 4.4 V 0.05 V Note: D1 and D2 depend on the value of R and C connected to Pin 3. They are specified here for the values: R = 120 k, and C = 180 pF. 6 MOTOROLA ANALOG IC DEVICE DATA MC44145 LOOP FILTER CALCULATION This section is not intended as a complete loop theory; its aim is merely to point out the peculiarities of the loop, and provide the user with enough information for the filter components selection. For a more in-depth covering, the cited reference should be consulted, especially [1]. The following remarks apply to the loop: * The loop frequency is 15 kHz. * In spite of the sampled nature of the loop, a continuous time approximation is possible if the loop bandwidth is sufficiently small. * Ripple on VC is a function of the loop bandwidth * The loop is a type II, 3rd order; however, since C2 is small, the pole it creates is far removed from the low frequency dominant poles, and the loop can be analyzed as a 2nd order loop. These remarks apply to the PFD: * Phase and frequency sensitive. * Independent of duty cycle. * PFD has 3 allowed states: up, down, hi-Z * The VCO is always pulled in the right direction (during acquisition). * PFD gain is higher near lock. The last two remarks imply that only the higher value need be taken into account, as acquisition will be slower, but always in the proper direction, whereas the higher gain will enter the action as soon as the error reaches 2. The following values are selected and defined (see Block Diagram): C2 = C/10 or less, to satisfy the requirement that the effect of C2 on the low frequency response of the loop be minimal, and similar to a second order loop. = 0.707 for the damping factor. i = 15625 x 2 the input pulsation. = RC as the loop filter. = o x p x R/(2 x x N) the loop gain. = x = 42 is the "normalized" loop gain. o = 57 x 106 [rad/Vs] (9.0 MHz/V). Stability analysis, with C2 = C/10 and = 2 ( = 0.707) gives a minimum value of 7.5 for the ratio i/ and to have some margin, a reasonable value can be 15 to 20 or higher [1]. Selecting i/ = 20, gives : = i/20 5000. With = 2, = 2/ = 400 s. Using = o x p x R/(2 x x N) and setting p = 60 A, and N an average value of 1000, we get R = 9.1 k. Then for = 400 s, C becomes 47 nF and C2, 4.7 nF. With these values, the loop natural frequency (n) and the loop bandwidth (3dB) can be calculated: n = [(o/N) x p/(2C)1/2 = 3400 and fn = 3400/2 = 540 Hz. 3dB = 2 x n = 1080 Hz (valid if is close to 0.707). References: [1] Charge-Pump Phase-Lock Loops, Floyd M. Gardner, IEEE transactions on communications, vol. com-28 no. 11 November 1980 [2] Phaselock Techniques, Floyd M. Gardner, J. Wiley & Sons, 1979 [3] Phase-Locked Loops, Roland E. Best, McGraw-Hill, 1984 [4] Phase-Locked Loop Systems, Motorola MOTOROLA ANALOG IC DEVICE DATA 7 MC44145 OUTLINE DIMENSIONS D SUFFIX PLASTIC PACKAGE CASE 751A-03 (SO-14) ISSUE F -A- 14 8 -B- 1 7 P 7 PL 0.25 (0.010) M B M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. G C R X 45 _ F -T- SEATING PLANE D 14 PL 0.25 (0.010) K M M S J TB A S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 8 *MC44145/D* MOTOROLA ANALOG IC DEVICE DATA MC44145/D |
Price & Availability of MC44145
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |